{
    "dataType": "CVE_RECORD",
    "dataVersion": "5.2",
    "cveMetadata": {
        "cveId": "CVE-2026-19576",
        "assignerOrgId": "e2e69745-5e70-4e92-8431-deb5529a81ad",
        "state": "PUBLISHED",
        "assignerShortName": "zephyr",
        "dateReserved": "2026-08-11T19:56:48.396Z",
        "datePublished": "2026-10-11T17:14:53.339Z",
        "dateUpdated": "2026-10-11T17:14:53.339Z"
    },
    "containers": {
        "cna": {
            "providerMetadata": {
                "orgId": "e2e69745-5e70-4e92-8431-deb5529a81ad",
                "shortName": "zephyr",
                "dateUpdated": "2026-10-11T17:14:53.339Z"
            },
            "title": "Stack out-of-bounds write in the Goodix GT911 touch controller driver from an unvalidated device-reported touch point count",
            "descriptions": [
                {
                    "lang": "en",
                    "value": "The Goodix GT9xx input driver in drivers/input/input_gt911.c reads the touch point count from the controller's status register and masks it with GT911_TOUCH_POINTS_MSK (0x0F), yielding a value of 0..15. In gt911_process() that value is used directly as the loop bound for filling point_reg[], a stack array sized to CONFIG_INPUT_GT911_MAX_TOUCH_POINTS, whose Kconfig range is 1..5 with a default of 1. No other check constrains the count; the driver relied only on a comment asserting that the controller had been programmed at init to report no more points than configured.\n\nEach loop iteration issues an I2C read of eight bytes straight into point_reg[i], so a controller that reports more points than the array holds causes up to 112 bytes of peer-supplied data to be written past the end of the array, over the stack frame of gt911_process() in the system workqueue thread. Two further loops then read out of bounds from the same array. Triggering it requires control of, or the ability to substitute, the I2C touch controller — plausible on the many supported boards where the GT9xx panel is a pluggable display module or shield rather than an on-PCB part; a spoofed device need only answer the init probes with a supported product ID and a checksum-valid config blob. The same overflow can also occur non-adversarially, with a GT9271-class panel that ignores the driver's touch-count programming and reports up to ten points, or with bus corruption of the single status byte.\n\nThe impact is an out-of-bounds stack write with fully attacker-chosen content executing at kernel privilege, i.e. potential control-flow hijack on the host MCU, in addition to out-of-bounds reads and crashes. The attack vector is physical/local hardware access only; there is no network, USB, or syscall path to the defect. The fix clamps the reported count with min() against CONFIG_INPUT_GT911_MAX_TOUCH_POINTS before any array indexing."
                }
            ],
            "affected": [
                {
                    "vendor": "zephyrproject",
                    "product": "zephyr",
                    "collectionURL": "https://github.com/zephyrproject-rtos/zephyr",
                    "packageName": "zephyr",
                    "defaultStatus": "unaffected",
                    "programFiles": [
                        "drivers/input/input_gt911.c"
                    ],
                    "programRoutines": [
                        {
                            "name": "gt911_process"
                        }
                    ],
                    "versions": [
                        {
                            "version": "4.0.0",
                            "status": "affected",
                            "versionType": "semver",
                            "lessThanOrEqual": "4.4.2"
                        }
                    ]
                }
            ],
            "references": [
                {
                    "url": "https://github.com/zephyrproject-rtos/zephyr/commit/42b52d571eb2113012c135276693042fd372fdea",
                    "name": "Fix commit",
                    "tags": [
                        "patch"
                    ]
                },
                {
                    "url": "https://github.com/zephyrproject-rtos/zephyr/security/advisories/GHSA-p7qh-fvwx-f7vr",
                    "name": "GHSA-p7qh-fvwx-f7vr"
                }
            ],
            "metrics": [
                {
                    "format": "CVSS",
                    "cvssV3_1": {
                        "version": "3.1",
                        "vectorString": "CVSS:3.1/AV:P/AC:L/PR:N/UI:N/S:U/C:H/I:H/A:H",
                        "baseScore": 6.8,
                        "baseSeverity": "MEDIUM"
                    }
                }
            ],
            "problemTypes": [
                {
                    "descriptions": [
                        {
                            "lang": "en",
                            "description": "bounds",
                            "cweId": "CWE-787",
                            "type": "CWE"
                        }
                    ]
                }
            ],
            "x_generator": {
                "engine": "cvelib 1.8.0"
            }
        }
    }
}